013 CIVIL ENGINEERING - CE
Q. 1 � Q. 25carries one mark each.
Q.1 There is no value of x that can simultaneously satisfy both the given equations.Therefore, find the �least squares error� solution to the two equations, i.e., find the value of that minimizes the sum of squares of the errors in the two equations. __________
2 3
4 1
Q.2 What is the minimum number of multiplications involved in computing the matrix product PQR? Matrix has 4 rows and 2 columns, matrix has 2 rows and 4 columns, and matrix has 4 rows and 1 column. __________
Q.3 A 1-h rainfall of 10 cm magnitude at a station has a return period of 50 years. The probability that a 1-h rainfall of magnitude 10 cm or more will occur in each oftwo successive years is:
(A) 0.04 | (B) | 0.2 | (C)0.02 | (D) 0.0004 | |
Q.4 | Maximum possible value of Compacting Factor for fresh (green) concrete is: | ||||
(A) 0.5 | (B) 1.0 | (C) 1.5 | (D) 2.0 | ||
Q.5 | As per IS 800:2007, the cross-section in which the extreme fiber can reach the yield stress, but | ||||
cannot develop the plastic moment of resistance due to failure by local buckling is classified as | |||||
(A) plastic section | (B) compact section | ||||
(C) semi-compact section | (D) slender section | ||||
Q.6 The creep strains are
(A) caused due to dead loads only
(B) caused due to live loads only
(C) caused due to cyclic loads only
(D) independent of loads
Q.7 As per IS 456:2000 for M20 grade concrete and plain barsin tension the design bond stress
1.2 .Further, IS 456:2000 permits this design bond stress value to be increased by 60 %
for HSD bars. The stress in theHSDreinforcing steel barsin tension, | 360 | . Find the |
required development length, , for HSD barsin terms of the bar diameter, | . __________ | |
Q.8 The �plane section remains plane� assumption in bending theory implies:
(A) strain profile is linear
(B) stress profile is linear
(C) both strain and stress profiles are linear (D)shear deformations are neglected
CE 4/16
CIVIL ENGINEERING - CE | |||||||
Q.9 | Two steel columns P (length | and yield strength | 250 | ) and Q (length 2 and yield | |||
strength | 500 | ) have the same cross-sections and end-conditions. The ratio of buckling | |||||
load of column P to that of column Q is: | |||||||
(A) 0.5 | (B) 1.0 | (C) 2.0 | (D) 4.0 | ||||
Q.10 | The pin-jointed 2-D truss is loaded with a horizontal force of 15 | at joint S and another 15 | |||||
vertical force at joint U, as shown.Find the force in member RS (in | ) and report your answer | ||||||
taking tension as positive and compression as negative. __________ | |||||||
4 m | 4 m | 4 m | |
R | S | 15 | |
4 m | |||
Q | V | U | T |
4 m
15
W
Q.11 | A symmetric I-section (with width of each flange | 50 | , thickness of each flange | 10 | , | |||||
depth of web = 100 mm, and thickness of web 10 | ) of steel is subjected to a shear force of | |||||||||
100 | . Find the magnitude of the shear stress(in | / | in the web at its junction with the top | |||||||
flange. __________ | ||||||||||
Q.12 | In its natural condition, a soil sample has a mass of 1.980 | and a volume of0.001 | . After | |||||||
being completely dried in an oven, the mass of the sample is 1.800 .Specific gravity | is 2.7. | |||||||||
Unit weight of water is 10 | / | . The degree of saturation of the soil is: | ||||||||
(A) 0.65 | (B) 0.70 | (C) | 0.54 | (D) 0.61 | ||||||
Q.13 | The ratio Nf/Nd is known as shape factor, where Nf is the number of flow lines and Nd is the | |||||||||
number of equipotential drops. Flow net is always drawn with a constant b/a ratio, where b and a | ||||||||||
are distances between two consecutive flow lines and equipotential lines, respectively. Assuming that b/a ratio remains the same, the shape factor of aflow net will change if the
(A) upstream and downstream heads are interchanged
(B) soil in the flow space is changed
(C) dimensions of the flow space are changed
(D) head difference causing the flow is changed
CE 5/16
Q.14 Following statementsare made on compacted soils, wherein DS stands forthe soils compacted on dry side of optimum moisture content and WS stands for thesoils compacted on wet side of optimum moisture content. Identify the incorrect statement.
(A) Soil structure is flocculated onDS and dispersed on WS.
(B) Construction pore water pressure is low on DS and high on WS. (C)On drying, shrinkage is high on DS and low on WS.
(D)On access to water, swelling is high on DS and low on WS.
Q.15 Four columns of a building are to be located within a plot size of 10 m x 10 m. The expected load on each column is 4000 kN. Allowable bearing capacity of the soil deposit is 100 kN/m2. The type of foundation best suited is
(A) isolated footing (B) raft foundation
(C) pile foundation (D)combined footing
Q.16 For subcritical flow in an open channel, the control section for gradually varied flow profiles is
(A) at the downstream end (B) at the upstream end
(C) at both upstream and downstream ends (D) at any intermediate section
Q.17 Group-I contains dimensionless parameters and Group- II contains the ratios.
Group-I | Group -II | |
P. Mach Number | 1. | Ratio of inertial force and gravitational force |
Q. Reynolds Number | 2. Ratio of fluid velocity and velocity of sound | |
R. Weber Number | 3. | Ratio of inertial force and viscous force |
S. Froude Number | 4. Ratio of inertial force and surface tension force | |
The correct match of dimensionless parameters in Group- I with ratios in Group-II is:
(A) P-3, Q-2, R-4, S-1 | (B) P-3, Q-4, R-2, S-1 | ||||
(C) P-2, Q-3, R-4, S-1 | (D) P-1, Q-3, R-2, S-4 | ||||
Q.18 | For a two dimensional | flow field, the stream functionis given as | 3 | y 2 | x2 . The |
2 |
magnitude of discharge occurring between the stream lines passing through points (0,3) and (3,4) is:
(A) 6 (B) 3 (C) 1.5 (D) 2
Q.19 An isohyet is a line joining points of | ||
(A) equal temperature | (B) | equal humidity |
(C) equal rainfall depth | (D) | equal evaporation |
CE 6/16
Q.20 Some of the water quality parameters are measured by titrating a water sample with a titrant. Group-I gives a list of parameters and Group-IIgives the list of titrants.
Group-I | Group-II | |
P.Alkalinity | 1. N/35.5 AgNO3 | |
Q. Hardness | 2. N/40 | Na2S2O3 |
R. Chloride | 3. N/50 | H2SO4 |
S. Dissolved oxygen | 4. N/50 | EDTA |
The correct match of water quality parameters in Group-I with titrants in Group-II is:
(A) P-1, Q-2, R-3, S-4 (B)P-3, Q-4, R-1, S-2
(C)P-2, Q-1, R-4, S-3 (D) P-4, Q-3, R-2, S-1
Q.21 A water treatment plant is designed to treat 1 m3/s of raw water. It has 14 sand filters. Surface area
of each filter is 50 m2. What is the loading rate (in | ) with two filters out of service for routine | ||
? | |||
backwashing? __________ | |||
Q.22 Selectthe strength parameter of concrete usedindesign of plain jointed cement concrete pavements from the following choices:
(A) Tensile strength
(B) Compressive strength
(C) Flexural strength
(D) Shear strength
Q.23 It was observed that 150 vehicles crossed a particular location of a highway ina duration of 30 minutes. Assuming that vehicle arrival follows a negative exponential distribution, find out the number of time headways greater than 5 seconds in the above observation? __________
Q.24 For two major roads with divided carriageway crossing at right angle,a full clover leaf interchange with four indirect ramps is provided. Following statements are made on turning movements of vehiclesto all directions from both roads. Identify the correct statement:
(A) Merging from left is possible,butdiverging to left is notpossible.
(B) Both merging from left and diverging to left arepossible.
(C) Merging from left is not possible,butdiverging to left is possible.
(D) Neithermergingfrom left nordivergingto leftispossible.
Q.25 The latitude and departure of a line AB are +78 m and -45.1 m, respectively. The whole circle bearing of the line AB is:
(A) 30� (B) 150� (C) 210� (D) 330�
CE 7/16
Q. 26 to Q. 55 carry two marks each.
Q.26 The state of 2D-stress at a point is given by the following matrix of stresses:
100 | 30 | |||
30 | 20 | |||
What is the magnitude of maximum shear stressin MPa? | ||||
(A) 50 | (B) 75 | (C) 100 | (D) 110 | |
Q.27 Find the magnitude of the error (correct to two decimal places) in the estimation of following integral using Simpson�s 13 Rule. Take the step length as 1. __________
4 x 4 10 dx
0
Q.28 | 6 | |||||||
The solution for | cos4 3 sin3 6 d is: | |||||||
0 | ||||||||
(A) 0 | (B) | 1 | (C) 1 | (D) | 8 | |||
15 | 3 | |||||||
Q.29 | Find the value of ? such that the function f (x) is a valid probability density function. __________ | |||||||
f (x)(x 1)(2 x) | for 1 x 2 | |||||||
0 | otherwise | |||||||
Q.30 Laplace equation for water flow in soils is given below.
2 H | 2 H | 2 H | 0 | |||
x2 | y 2 | z 2 | ||||
Head H does not vary in y and z directions.
Boundary conditions are: at x = 0, H = 5;and dHdx 1 .
What is the value of H at x = 1.2? __________
CE 8/16
Q.31 All members in the rigid-jointed frame shown are prismatic and have the same flexural stiffness .
Find the magnitude of the bending moment at Q (in | ) due to the given loading. __________ | ||||||
3 m | 4 m | ||||||
S | |||||||
2 m | |||||||
P | T | R | |||||
2 m | 100 kNm | ||||||
Q | |||||||
Q.32 A uniform beam | in the form of a quarter-circle of radius is fixed at end | ||||||
and free at the end , where a load | is applied as shown. The vertical downward displacement, | ||||||
, at the loaded point | is given by: | . Find the value of (correct to 4-decimal | |||||
places). __________ | |||||||
Q | |||||||
W | |||||||
P | R | ||||||
CE 9/16
CIVIL ENGINEERING - CE | |
Q.33 A | niform bea m weighing 1800 is supported at E and F by cable ABCD. Determine the tension |
(in | in segm ent AB of this cable (correct to 1-decimal place). Assume the cables ABCD, BE and |
CF to be weightless. __________
Q.34 Be am | has internal hinges in spans | and | as shown. The beam may be subjected to a | ||||
moving distributed vertical load of maximum intensity 4 | ? of any length anywhere on the | ||||||
bea m. The maximum absolute value of the shear force (in | ) that can occur due to this loading | ||||||
just to the right of support Q shall be: | |||||||
P | Q | R | S | ||||
5 m | 5 m | 20 m | 5 m | 5 m | |
(A ) 30 | ( B) 40 | (C) 45 | (D) 55 | ||
Q.35 A rectangular c oncrete beam 250 | wide and 600 | deep is pre-stressed by means of 16 high | |||
tensile wires, e ach of 7 mm diameter, located at200 | fro m the bottom face of the beamat a | ||||
given section. If the effective pre-stress in the wires is700 | , what is the maximum sagging | ||||
ben ding moment (in | ) (correct to 1-decimal place) due to live loadthat this sectionof the beam | ||||
can withstand without causing tensile stress at the bottom face of the beam ? Neglect the effect of dea d load of beam. __________
CE 10/16
CIVIL ENGINEERING - CE | |
Q.36 The soil profile below a lake with water level at elevation | 0 m and lake bottom at elevation |
10 m is shown in the figure, where k is the permeability coefficient. A piezometer (stand pipe) installed in the sand layer shows a reading of +10 m elevation. Assume that thepiezometric headis uniform in the sand layer. The quantity of water (in m3/s) flowing into the lake from the sand layer through the silt layer per unit area of the lake bed is:
+10 | Stand pipe | ||||||||||||
0 | |||||||||||||
Lake | |||||||||||||
Lake bottom | |||||||||||||
-10 | |||||||||||||
Silt (k = 10-6 m/s) | |||||||||||||
-30 | |||||||||||||
Sand | |||||||||||||
-40 | (under artesian pressure) | ||||||||||||
Rock | |||||||||||||
(A) 1.5 x 10-6 | (B) 2.0 x 10-6 | ||||||||||||
(C) 1.0 x 10-6 | (D) 0.5 x 10-6 | ||||||||||||
Q.37 The soil profile above the rock surface for a 25oinfinite slope is shown in the figure, where su is the undrained shear strength and t is total unit weight. The slip will occur at a depth of
(A) 8.83 m (B) 9.79 m (C) 7.83 m (D) 6.53 m
CE 11/16
Q.38 Two different soil types (Soil 1 and Soil 2) are used as backfill behind a retaining wall as shown in the figure, where t is total unit weight, and c' and ' are effective cohesion and effective angle of
shearing resistance. The resultant active earth forceper unit length (in kN/m) acting on the wall is:
Retaining wall | ||||
Soil 1: | ||||
2 m | t = 15 kN/m3; c' = 0; ' = 30o | |||
2 m | Soil 2: | |||
t = 20 kN/m3; c' = 0; ' = 40o | ||||
(A) 31.7 | (B) 35.2 | (C) 51.8 | (D) | 57.0 |
Q.39 A 2 km long pipe of 0.2 m diameter connects two reservoirs. The difference between water levels in the reservoirs is 8 m. The Darcy-Weisbachfriction factor of the pipe is 0.04. Accounting for frictional, entry and exit losses, the velocity in the pipe (in m/s) is:
(A) 0.63 (B)0.35 (C) 2.52 (D) 1.25
Q.40 The normal depth in a wide rectangular channel is increased by 10%. The percentage increase in the discharge in the channel is:
(A) 20.1 (B) 15.4 (C) 10.5 (D) 17.2
Q.41 The transplantation of rice requires 10 days and total depth of water required during transplantation is 48 cm. During transplantation, there is an effective rainfall (useful for irrigation) of 8 cm. The duty of irrigation water (in hectares/cumec) is:
(A) 612 | (B) 216 | (C)300 | (D) 108 | |||
Q.42 | A settling tank in a water treatment plant is designed for a surface overflow rate of30 | . | ||||
? | ||||||
Assumespecific gravity of sedimentparticles = 2.65, density of water (?) = 1000 kg/m3, dynamic | ||||||
viscosity of water (�)=0.001 N.s/m2,and Stokes� lawisvalid.The approximate minimum size of | ||||||
particles that would be completely removed is: | ||||||
(A) 0.01mm | (B) 0.02 mm(C) 0.03 mm(D) 0.04 mm | |||||
Q.43 A student began experiment for determination of 5 -day, 20�C BOD on Monday. Since the 5thday fell on Saturday, the final DO readings were taken on next Monday. On calculation, BOD (i.e. 7 day, 20�C) was found to be 150 mg/L. What would be the5-day, 20�C BOD (in mg/L)? Assume value of BOD rate constant (k) at standard temperature of 20�C as 0.23/day (base e). __________
CE 12/16
Q.44 Elevation and temperature data for a place are tabulated below:
Elevation, m | Temperature, �C |
4 | 21.25 |
444 | 15.70 |
Based on the above data, lapse rate can be referred as:
(A) Super-adiabatic (B) Neutral (C) Sub-adiabatic (D) Inversion
Q.45 The percent voids in mineral aggregate (VMA) and percent air voids (Vv) in a compacted cylindrical bituminous mix specimen are 15 and 4.5respectively. The percent voids filled with bitumen (VFB) for this specimen is:
(A) 24 (B) 30 (C) 54 (D) 70
Q.46 Following bearings are observed while traversing with a compass.
Line | Fore Bearing | Back Bearing |
AB | 126�45� | 308�00� |
BC | 49�15� | 227�30� |
CD | 340�30� | 161�45� |
DE | 258�30� | 78�30� |
EA | 212�30� | 31�45� |
After applying the correction due to local attraction, the corrected fore bearing of line BC will be:
(A) 48�15� (B)50�15� (C) 49�45� (D) 48�45�
Q.47 A theodolite is set up at station A and a 3 m long staff is held vertically at station B. The depression angle reading at 2.5 m marking on the staffis 6�10�. The horizontal distance between A and B is 2200 m. Height of instrument at station A is 1.1 m and R.L. of A is 880.88 m.Apply the curvature and refraction correction, and determine the R.L. of B (in m). __________
Common Data Questions
Common Data for Questions 48 and 49:
A propped cantilever made of a prismatic steel beam is subjected to a concentrated load P at mid span as | |||||||
shown. | P | ||||||
R | |||||||
1.5m | 1.5m | ||||||
Q.48 If load | 80 | ,find the reaction (in | ) (correct to 1-decimal place)using elastic analysis. | ||||
__________ | |||||||
Q.49 If the magnitude of load beam section is 90 analysis. __________
is increased till collapse and the plastic moment carrying capacity of steel , determine reaction (in )(correct to 1-decimal place) using plastic
CE 13/16
Common Data for Questions 50 and 51:
For a portion of national highway where a descending gradient of 1 in 25 meets with an ascending gradient of 1 in 20, a valley curve needs to be designed for a vehicle travelling at 90 kmphbased on the following conditions.
(i) headlight sight distance equalto the stopping sight distance (SSD) of a level terrain consideringlength of valley curve> SSD.
(ii) comfort condition with allowablerate of change of centrifugal acceleration = 0.5 m/sec3.
Assume total reaction time = 2.5 seconds; coefficient of longitudinal friction of the pavement= 0.35; height of head light of the vehicle =0.75 m; andbeam angle = 1�.
Q.50 What is the length of valley curve (in m) based on the head light sight distance condition?
__________
Q.51 What is the length of valley curve (in m)based on the comfort condition? __________
Linked Answer Questions
Statement for Linked Answer Questions 52 and 53:
A multistory building with a basement is to be constructed. The top 4 m consists of loose silt, below which dense sand layer is present up to a great depth. Ground water table is at the surface. The foundation consists of the basement slab of 6 m width which will rest on the top of dense sand as shown in the figure. For
dense sand, saturated unit weight = 20kN/m3, and bearing capacity factors Nq = 40 and N = 45. For loose
silt, saturated unit weight = 18kN/m3 , Nq = 15 and N = 20.Effective cohesion c' is zero for both soils.Unit weight of water is 10 kN/m3. Neglect shape factor and depth factor.
Average elastic modulus E and Poisson�s ratio of dense sand is 60 x 103kN/m2 and 0.3 respectively.
Ground surface | ||||||||
Loose silt | ||||||||
Loose silt | Basement | |||||||
4 m | ||||||||
Foundation slab | ||||||||
6 m
Dense sand
Q.52 Using factor of safety = 3, the net safe bearing capacity (in kN/m2) of the foundation is:
(A) 610 (B) 320 (C) 983 (D) 693
Q.53 The foundation slab is subjected to vertical downward stresses equal to net safe bearing capacity derived in the above question. Using influence factor If = 2.0, and neglecting embedment depth and
rigidity corrections, the immediate settlement of the dense sand layer will be:
(A) 58 mm | (B) 111 mm | (C) 126 mm | (D) 179 mm |
CE 14/16
Statement for Linked Answer Questions 54 and 55:
At a station, Storm I of 5 hour duration with intensity 2 cm/h resulted in a runoff of 4 cm and Storm II of 8 hour duration resulted in a runoff of 8.4 cm. Assume that the ?-index is the same for both the storms.
Q.54 The ?-index (in cm/h) is:
(A)1.2 (B)1.0 (C)1.6 (D) 1.4
Q.55 The intensity of storm II (in cm/h) is:
(A) 2.00 (B)1.75 (C)1.50 (D)2.25
General Aptitude (GA) Questions
Q. 56 � Q. 60 carry one mark each.
Q.56 A number is as much greater than 75 as it is smaller than 117. The number is:
(A) 91 (B) 93 (C) 89 (D) 96
Q.57 The professor ordered to the students to go out of the class.
I II III IV
Which of the above underlined parts of the sentence is grammatically incorrect?
(A) I (B) II (C) III (D) IV
Q.58 Which of the following options is the closest in meaning to the word given below:
Primeval
(A) Modern | (B) Historic |
(C) Primitive | (D) Antique |
Q.59 Friendship, no matter how _________it is, has its limitations.
(A) cordial
(B) intimate
(C) secret
(D) pleasant
Q.60 Select the pair that best expresses a relationship similar to that expressed in the pair:
Medicine: Health
(A) Science: Experiment (B) Wealth: Peace
(C) Education: Knowledge (D) Money: Happiness
CE 15/16
CIVIL ENGINEERING - CE | ||||||||
Q. 61 to Q. 65 carry two marks each. | ||||||||
Q.61 X and Y are two positive real numbers such that 2 | 6 and | 2 | 8. For which of the | |||||
following values of | , the function | , | 3 | 6 | will give maximum value? | |||
(A) (4/3, 10/3) | ||||||||
(B) (8/3, 20/3) | ||||||||
(C) (8/3, 10/3) | ||||||||
(D) (4/3, 20/3) | ||||||||
Q.62 If |4 | 7| 5 then the values of 2 | | | | | | is: | |||||
(A) | 2, 1/3 | (B) 1/2, 3 | (C) | 3/2, 9 | (D) | 2/3, 9 | ||
Q.63 Following table provides figures (in rupees) on annual expenditure of a firm for two years - 2010 and 2011.
Category | 2010 | 2011 |
Raw material | 5200 | 6240 |
Power & fuel | 7000 | 9450 |
Salary & wages | 9000 | 12600 |
Plant & machinery | 20000 | 25000 |
Advertising | 15000 | 19500 |
Research & Development | 22000 | 26400 |
In 2011, which of the following two categories have registered increase by same percentage?
(A) Raw material and Salary & wages
(B) Salary & wages and Advertising
(C) Power & fuel and Advertising
(D) Raw material and Research & Development
Q.64 A firm is selling its product at Rs. 60 per unit. The total cost of production is Rs. 100 and firm is earning total profit of Rs. 500. Later, the total cost increased by 30%. By what percentage the price should be increased to maintained the same profit level.
(A) 5 (B) 10 (C) 15 (D) 30
Q.65 Abhishek is elder to Savar.
Savar is younger to Anshul.
Which of the given conclusions is logically valid and is inferred from the above statements?
(A) Abhishek is elder to Anshul
(B) Anshul is elder to Abhishek
(C) Abhishek and Anshul are of the same age
(D) No conclusion follows
END OF THE QUESTION PAPER
CE
